summaryrefslogtreecommitdiff
path: root/target/foxg20/patches
diff options
context:
space:
mode:
Diffstat (limited to 'target/foxg20/patches')
-rw-r--r--target/foxg20/patches/foxg20.patch471
1 files changed, 0 insertions, 471 deletions
diff --git a/target/foxg20/patches/foxg20.patch b/target/foxg20/patches/foxg20.patch
deleted file mode 100644
index d564c71fb..000000000
--- a/target/foxg20/patches/foxg20.patch
+++ /dev/null
@@ -1,471 +0,0 @@
-diff -Nur linux-2.6.34.orig/arch/arm/include/asm/setup.h linux-2.6.34/arch/arm/include/asm/setup.h
---- linux-2.6.34.orig/arch/arm/include/asm/setup.h 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/include/asm/setup.h 2010-05-25 20:26:06.083473207 +0200
-@@ -18,6 +18,8 @@
-
- #define COMMAND_LINE_SIZE 1024
-
-+const char *get_system_type(void);
-+
- /* The list ends with an ATAG_NONE node. */
- #define ATAG_NONE 0x00000000
-
-diff -Nur linux-2.6.34.orig/arch/arm/Kconfig linux-2.6.34/arch/arm/Kconfig
---- linux-2.6.34.orig/arch/arm/Kconfig 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/Kconfig 2010-05-25 20:26:06.103473096 +0200
-@@ -20,6 +20,8 @@
- select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
- select HAVE_GENERIC_DMA_COHERENT
- select HAVE_KERNEL_GZIP
-+ select HAVE_KERNEL_BZIP2
-+ select HAVE_KERNEL_LZMA
- select HAVE_KERNEL_LZO
- select HAVE_PERF_EVENTS
- select PERF_USE_VMALLOC
-diff -Nur linux-2.6.34.orig/arch/arm/kernel/setup.c linux-2.6.34/arch/arm/kernel/setup.c
---- linux-2.6.34.orig/arch/arm/kernel/setup.c 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/kernel/setup.c 2010-05-25 20:26:06.150978830 +0200
-@@ -790,8 +790,12 @@
-
- static int c_show(struct seq_file *m, void *v)
- {
-+ unsigned long n = (unsigned long) v - 1;
- int i;
-
-+ if (n == 0)
-+ seq_printf(m, "system type\t\t: %s\n", get_system_type());
-+
- seq_printf(m, "Processor\t: %s rev %d (%s)\n",
- cpu_name, read_cpuid_id() & 15, elf_platform);
-
-diff -Nur linux-2.6.34.orig/arch/arm/mach-at91/at91sam9260_devices.c linux-2.6.34/arch/arm/mach-at91/at91sam9260_devices.c
---- linux-2.6.34.orig/arch/arm/mach-at91/at91sam9260_devices.c 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/mach-at91/at91sam9260_devices.c 2010-05-25 20:26:06.190979002 +0200
-@@ -454,7 +454,15 @@
- .sda_is_open_drain = 1,
- .scl_pin = AT91_PIN_PA24,
- .scl_is_open_drain = 1,
-+#if defined(CONFIG_MACH_FOXG20)
-+ /* Some I2C devices are limited to 100 kHz and i2c-gpio.h
-+ * says "frequency is (500 / udelay) kHz" so 5 is best (and is
-+ * used in i2c-gpio.c)
-+ */
-+ .udelay = 5, /* ~100 kHz */
-+#else
- .udelay = 2, /* ~100 kHz */
-+#endif
- };
-
- static struct platform_device at91sam9260_twi_device = {
-diff -Nur linux-2.6.34.orig/arch/arm/mach-at91/board-foxg20.c linux-2.6.34/arch/arm/mach-at91/board-foxg20.c
---- linux-2.6.34.orig/arch/arm/mach-at91/board-foxg20.c 1970-01-01 01:00:00.000000000 +0100
-+++ linux-2.6.34/arch/arm/mach-at91/board-foxg20.c 2010-05-25 20:26:06.230978938 +0200
-@@ -0,0 +1,376 @@
-+/*
-+ * Copyright (C) 2005 SAN People
-+ * Copyright (C) 2008 Atmel
-+ * Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/types.h>
-+#include <linux/init.h>
-+#include <linux/mm.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/at73c213.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
-+#include <linux/clk.h>
-+#include <linux/w1-gpio.h>
-+
-+#include <mach/hardware.h>
-+#include <asm/setup.h>
-+#include <asm/mach-types.h>
-+#include <asm/irq.h>
-+
-+#include <asm/mach/arch.h>
-+#include <asm/mach/map.h>
-+#include <asm/mach/irq.h>
-+
-+#include <mach/board.h>
-+#include <mach/gpio.h>
-+#include <mach/at91sam9_smc.h>
-+
-+#include "sam9_smc.h"
-+#include "generic.h"
-+
-+/*
-+ * The FOX hardware comes as the "Netus" board with just the cpu, ram,
-+ * dataflash and two header connectors. This is plugged into the Fox board
-+ * which provides the ethernet, usb, rtc, leds, switch, ...
-+ * Other version of the Fox board are planned which could contain
-+ * both NAND and sound (WM8731).
-+ *
-+ * By default USART4 and USART5 are not enabled (freeing up those pins
-+ * for general use)
-+ *
-+ * Note: Enabling the NAND without a NAND device present doesn't cause
-+ * any issues as on boot the probe will fail.
-+ */
-+/* #define FOXG20_NAND */
-+/* #define FOXG20_WM8731 */
-+/* #define FOX_USART4 */
-+/* #define FOX_USART5 */
-+
-+const char *get_system_type(void)
-+{
-+ return "FoxBoard FOXG20";
-+}
-+
-+static void __init foxg20_map_io(void)
-+{
-+ /* Initialize processor: 18.432 MHz crystal */
-+ at91sam9260_initialize(18432000);
-+
-+ /* DBGU on ttyS0. (Rx & Tx only) */
-+ at91_register_uart(0, 0, 0);
-+
-+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-+ | ATMEL_UART_RI);
-+
-+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-+
-+ /* USART2 on ttyS3. (Rx & Tx only) */
-+ at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-+
-+ /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
-+ at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_CTS | ATMEL_UART_RTS);
-+
-+#if defined(FOX_USART4)
-+ /* USART4 on ttyS5. (Rx & Tx only) */
-+ at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-+#endif
-+
-+#if defined(FOX_USART5)
-+ /* USART5 on ttyS6. (Rx & Tx only) */
-+ at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-+#endif
-+
-+ /* set serial console to ttyS0 (ie, DBGU) */
-+ at91_set_serial_console(0);
-+}
-+
-+static void __init foxg20_init_irq(void)
-+{
-+ at91sam9260_init_interrupts(NULL);
-+}
-+
-+
-+/*
-+ * USB Host port
-+ */
-+static struct at91_usbh_data __initdata foxg20_usbh_data = {
-+ .ports = 2,
-+};
-+
-+/*
-+ * USB Device port
-+ */
-+static struct at91_udc_data __initdata foxg20_udc_data = {
-+ .vbus_pin = AT91_PIN_PC6,
-+ .pullup_pin = 0, /* pull-up driven by UDC */
-+};
-+
-+
-+/*
-+ * SPI devices.
-+ */
-+static struct spi_board_info foxg20_spi_devices[] = {
-+#if !defined(CONFIG_MMC_AT91)
-+ {
-+ .modalias = "mtd_dataflash",
-+ .chip_select = 1,
-+ .max_speed_hz = 15 * 1000 * 1000,
-+ .bus_num = 0,
-+ },
-+#endif
-+};
-+
-+
-+/*
-+ * MACB Ethernet device
-+ */
-+static struct at91_eth_data __initdata foxg20_macb_data = {
-+ .phy_irq_pin = AT91_PIN_PA7,
-+ .is_rmii = 1,
-+};
-+
-+
-+#ifdef FOXG20_NAND
-+/* The Fox doesn't have NAND memory */
-+/*
-+ * NAND flash
-+ */
-+static struct mtd_partition __initdata foxg20_nand_partition[] = {
-+ {
-+ .name = "Bootstrap",
-+ .offset = 0,
-+ .size = 4 * SZ_1M,
-+ },
-+ {
-+ .name = "Partition 1",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 60 * SZ_1M,
-+ },
-+ {
-+ .name = "Partition 2",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL,
-+ },
-+};
-+
-+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-+{
-+ *num_partitions = ARRAY_SIZE(foxg20_nand_partition);
-+ return foxg20_nand_partition;
-+}
-+
-+/* det_pin is not connected */
-+static struct atmel_nand_data __initdata foxg20_nand_data = {
-+ .ale = 21,
-+ .cle = 22,
-+ .rdy_pin = AT91_PIN_PC13,
-+ .enable_pin = AT91_PIN_PC14,
-+ .partition_info = nand_partitions,
-+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-+ .bus_width_16 = 1,
-+#else
-+ .bus_width_16 = 0,
-+#endif
-+};
-+
-+static struct sam9_smc_config __initdata foxg20_nand_smc_config = {
-+ .ncs_read_setup = 0,
-+ .nrd_setup = 2,
-+ .ncs_write_setup = 0,
-+ .nwe_setup = 2,
-+
-+ .ncs_read_pulse = 4,
-+ .nrd_pulse = 4,
-+ .ncs_write_pulse = 4,
-+ .nwe_pulse = 4,
-+
-+ .read_cycle = 7,
-+ .write_cycle = 7,
-+
-+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-+ .tdf_cycles = 3,
-+};
-+
-+static void __init foxg20_add_device_nand(void)
-+{
-+ /* setup bus-width (8 or 16) */
-+ if (foxg20_nand_data.bus_width_16)
-+ foxg20_nand_smc_config.mode |= AT91_SMC_DBW_16;
-+ else
-+ foxg20_nand_smc_config.mode |= AT91_SMC_DBW_8;
-+
-+ /* configure chip-select 3 (NAND) */
-+ sam9_smc_configure(3, &foxg20_nand_smc_config);
-+
-+ at91_add_device_nand(&foxg20_nand_data);
-+}
-+#endif
-+
-+
-+/*
-+ * MCI (SD/MMC)
-+ * det_pin, wp_pin and vcc_pin are not connected
-+ */
-+static struct at91_mmc_data __initdata foxg20_mmc_data = {
-+ .slot_b = 1,
-+ .wire4 = 1,
-+};
-+
-+
-+/*
-+ * LEDs
-+ */
-+static struct gpio_led foxg20_leds[] = {
-+ { /* user led, red */
-+ .name = "user_led",
-+ .gpio = AT91_PIN_PC7,
-+ .active_low = 0,
-+ .default_trigger = "heartbeat",
-+ },
-+};
-+
-+
-+/*
-+ * GPIO Buttons
-+ */
-+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-+static struct gpio_keys_button foxg20_buttons[] = {
-+ {
-+ .gpio = AT91_PIN_PC4,
-+ .code = BTN_1,
-+ .desc = "Button 1",
-+ .active_low = 1,
-+ .wakeup = 1,
-+ },
-+};
-+
-+static struct gpio_keys_platform_data foxg20_button_data = {
-+ .buttons = foxg20_buttons,
-+ .nbuttons = ARRAY_SIZE(foxg20_buttons),
-+};
-+
-+static struct platform_device foxg20_button_device = {
-+ .name = "gpio-keys",
-+ .id = -1,
-+ .num_resources = 0,
-+ .dev = {
-+ .platform_data = &foxg20_button_data,
-+ }
-+};
-+
-+static void __init foxg20_add_device_buttons(void)
-+{
-+ at91_set_gpio_input(AT91_PIN_PC4, 1); /* btn1 */
-+ at91_set_deglitch(AT91_PIN_PC4, 1);
-+
-+ platform_device_register(&foxg20_button_device);
-+}
-+#else
-+static void __init foxg20_add_device_buttons(void) {}
-+#endif
-+
-+
-+#if !defined(FOXG20_WM8731)
-+#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-+static struct w1_gpio_platform_data w1_gpio_pdata = {
-+ /* If you choose to use a pin other than PB16 it needs to be 3.3V */
-+ .pin = AT91_PIN_PB16,
-+ .is_open_drain = 1,
-+};
-+
-+static struct platform_device w1_device = {
-+ .name = "w1-gpio",
-+ .id = -1,
-+ .dev.platform_data = &w1_gpio_pdata,
-+};
-+
-+static void __init at91_add_device_w1(void)
-+{
-+ at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-+ at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-+ platform_device_register(&w1_device);
-+}
-+
-+#endif
-+#endif
-+
-+
-+static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
-+ {
-+ I2C_BOARD_INFO("24c512", 0x50),
-+#ifdef FOXG20_WM8731
-+ I2C_BOARD_INFO("wm8731", 0x1b),
-+#endif
-+ },
-+};
-+
-+
-+static void __init foxg20_board_init(void)
-+{
-+ /* Serial */
-+ at91_add_device_serial();
-+ /* USB Host */
-+ at91_add_device_usbh(&foxg20_usbh_data);
-+ /* USB Device */
-+ at91_add_device_udc(&foxg20_udc_data);
-+ /* SPI */
-+ at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
-+#ifdef FOXG20_NAND
-+ /* The Fox doesn't have NAND memory */
-+ /* NAND */
-+ foxg20_add_device_nand();
-+#endif
-+ /* Ethernet */
-+ at91_add_device_eth(&foxg20_macb_data);
-+ /* MMC */
-+ at91_add_device_mmc(0, &foxg20_mmc_data);
-+ /* I2C */
-+ at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
-+ /* LEDs */
-+ at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
-+ /* Push Buttons */
-+ foxg20_add_device_buttons();
-+#ifdef FOXG20_WM8731
-+ /* The Fox doesn't have this sound chip */
-+ /* PCK0 provides MCLK to the WM8731 */
-+ at91_set_B_periph(AT91_PIN_PC1, 0);
-+ /* SSC (for WM8731) */
-+ at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-+#else
-+#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-+ at91_add_device_w1();
-+#endif
-+#endif
-+}
-+
-+MACHINE_START(AT91SAM9G20EK, "Acme Systems FOXG20")
-+ /* Maintainer: Lee McLoughlin */
-+ .phys_io = AT91_BASE_SYS,
-+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
-+ .boot_params = AT91_SDRAM_BASE + 0x100,
-+ .timer = &at91sam926x_timer,
-+ .map_io = foxg20_map_io,
-+ .init_irq = foxg20_init_irq,
-+ .init_machine = foxg20_board_init,
-+MACHINE_END
-diff -Nur linux-2.6.34.orig/arch/arm/mach-at91/Kconfig linux-2.6.34/arch/arm/mach-at91/Kconfig
---- linux-2.6.34.orig/arch/arm/mach-at91/Kconfig 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/mach-at91/Kconfig 2010-05-25 20:26:06.270978491 +0200
-@@ -360,6 +360,15 @@
- Select this if you are using a Eukrea Electromatique's
- CPU9G20 Board <http://www.eukrea.com/>
-
-+config MACH_FOXG20
-+ bool "Acme Systems FOX G20"
-+ select HAVE_AT91_DATAFLASH_CARD
-+ select HAVE_NAND_ATMEL_BUSWIDTH_16
-+ depends on ARCH_AT91SAM9G20
-+ help
-+ Select this if you are using Acme Systems
-+ FOX Board G20 <http://netus.acmesystems.it>
-+
- endif
-
- # ----------------------------------------------------------
-diff -Nur linux-2.6.34.orig/arch/arm/mach-at91/Makefile linux-2.6.34/arch/arm/mach-at91/Makefile
---- linux-2.6.34.orig/arch/arm/mach-at91/Makefile 2010-05-16 23:17:36.000000000 +0200
-+++ linux-2.6.34/arch/arm/mach-at91/Makefile 2010-05-25 20:26:06.310978635 +0200
-@@ -67,6 +67,9 @@
- # AT91SAM9G45 board-specific support
- obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o
-
-+# FOXG20 board-specific support
-+obj-$(CONFIG_MACH_FOXG20) += board-foxg20.o
-+
- # AT91CAP9 board-specific support
- obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o
-
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-08 14:26:09 +0000